By john. Door. Published at Tuesday, October 30th, 2018 - 14:50:57 PM.
Pocket door : A pocket door is a sliding door that disappears, when fully open, into a compartment in the adjacent wall. Pocket doors are used for architectural effect, or when there is no room for the swing of a hinged door. They can travel on rollers suspended from an overhead track or also feature tracks or guides along the floor. Both single- and double-door versions are used, depending on how wide an entry is desired.
Other types of Hinges : Hinge (film) A short film by Aldo Emiliano Velasco (Echo) about the origin of the hinge. Butler tray hinge Fold to 90 degrees and also snap flat. They are for tables that have a tray top for serving. Card table hinge Mortised into edge of antique or reproduction card tables and allow the top to fold onto itself. Drop-leaf table hinge Mounted under the surface of a table with leaves that drop down. They are most commonly used with rule joints. Piano hinge a long hinge, originally used for piano lids, but now used in many other applications where a long hinge is needed. Living hinge a hinge consisting of material that flexes
History Of Door : The earliest in records are those represented in the paintings of some Egyptian tombs, in which they are shown as single or double doors, each in a single piece of wood. Doors were once believed to be the literal doorway to the afterlife, and some doors leading to important places included designs of the afterlife. In Egypt, where the climate is intensely dry, there would be no fear of their warping, but in other countries it would be necessary to frame them, which according to Vitruvius (iv. 6.) was done with stiles (sea/si) and rails (see: Frame and panel): the spaces enclosed being filled with panels (tympana) let into grooves made in the stiles and rails. The stiles were the vertical boards, one of which, tenoned or hinged, is known as the hanging stile, the other as the middle or meeting stile. The horizontal cross pieces are the top rail, bottom rail, and middle or intermediate rails. The most ancient doors were made of timber, such as those referred to in the Biblical depiction of King Solomons temple being in olive wood (I Kings vi. 31-35), which were carved and overlaid with gold. The doors dwelt upon in Homer would appear to have been cased in silver or brass. Besides olive wood, elm, cedar, oak and cypress were used. A 5,000-year-old door has been found by archaeologists in Switzerland. All ancient doors were hung by pivots at the top and bottom of the hanging stile which worked in sockets in the lintel and sill, the latter being always in some hard stone such as basalt or granite. Those found at Nippur by Dr. Hilprecht dating from 2000 B.C. were in dolerite. The tenons of the gates at Balawat were sheathed with bronze (now in the British Museum). These doors or gates were hung in two leaves, each about 8 ft 4 in (2.54 m) wide and 27 ft (8.2 m). high; they were encased with bronze bands or strips, 10 in. high, covered with repouss decoration of figures, etc. The wood doors would seem to have been about 3 in. thick, but the hanging stile was over 14 inches (360 mm) diameter. Other sheathings of various sizes in bronze have been found, which proves this to have been the universal method adopted to protect the wood pivots. In the Hauran in Syria, where timber is scarce the doors were made in stone, and one measuring 5 ft 4 in (1.63 m) by 2 ft 7 in (0.79 m) is in the British Museum; the band on the meeting stile shows that it was one of the leaves of a double door. At Kuffeir near Bostra in Syria, Burckhardt found stone doors, 9 to 10 ft (3.0 m). high, being the entrance doors of the town. In Etruria many stone doors are referred to by Dennis. The ancient Greek and Roman doors were either single doors, double doors, triple doors, sliding doors or folding doors, in the last case the leaves were hinged and folded back. In Eumachia, is a painting of a door with three leaves. In the tomb of Theron at Agrigentum there is a single four-panel door carved in stone. In the Blundell collection is a bas-relief of a temple with double doors, each leaf with five panels. Among existing examples, the bronze doors in the church of SS. Cosmas and Damiano, in Rome, are important examples of Roman metal work of the best period; they are in two leaves, each with two panels, and are framed in bronze. Those of the Pantheon are similar in design, with narrow horizontal panels in addition, at the top, bottom and middle. Two other bronze doors of the Roman period are in the Lateran Basilica. The Greek scholar Heron of Alexandria created the earliest known automatic door in the 1st century AD during the era of Roman Egypt. The first foot-sensor-activated automatic door was made in China during the reign of Emperor Yang of Sui (r. 604–618), who had one installed for his royal library. The first automatic gate operators were later created in 1206 by Arab inventor Al-Jazari. Copper and its alloys were integral in medieval architecture. The doors of the church of the Nativity at Bethlehem (6th century) are covered with plates of bronze, cut out in patterns. Those of Hagia Sophia at Constantinople, of the 8th and 9th century, are wrought in bronze, and the west doors of the cathedral of Aix-la-Chapelle (9th century), of similar manufacture, were probably brought from Constantinople, as also some of those in St. Marks, Venice. The bronze doors on the Aachen Cathedral in Germany date back to about AD 800. Bronze baptistery doors at the Cathedral of Florence were completed in 1423 by Ghiberti.(For more information, see: Copper in architecture). Of the 11th and 12th centuries there are numerous examples of bronze doors, the earliest being one at Hildesheim, Germany(1015). The Hildesheim design affected the concept of Gniezno door in Poland. Of others in South Italy and Sicily, the following are the finest: in Sant Andrea, Amalfi (1060); Salerno (1099); Canosa(1111); Troia, two doors (1119 and 1124); Ravello (1179), by Barisano of Trani, who also made doors for Trani cathedral; and in Monreale and Pisa cathedrals, by Bonano of Pisa. In all these cases the hanging stile had pivots at the top and bottom. The exact period when the hinge was substituted is not quite known, but the change apparently brought about another method of strengthening and decorating doors, viz, with wrought-iron bands of infinite varieties of design. As a rule three bands from which the ornamental work springs constitute the hinges, which have rings outside the hanging stiles fitting on to vertical tenons run into the masonry or wooden frame. There is an early example of the 12th century in Lincoln; in France the metal work of the doors of Notre Dame at Paris is perhaps the most beautiful in execution, but examples are endless throughout France and England. Returning to Italy, the most celebrated doors are those of the Battistero di San Giovanni (Florence), which together with the door frames are all in bronze, the borders of the latter being perhaps the most remarkable: the modeling of the figures, birds and foliage of the south doorway, by Andrea Pisano (1330), and of the east doorway by Ghiberti (1425–1452), are of great beauty; in the north door (1402–1424) Ghiberti adopted the same scheme of design for the paneling and figure subjects in them as Andrea Pisano, but in the east door the rectangular panels are all filled, with bas-reliefs, in which Scripture subjects are illustrated with innumerable figures, these being probably the gates of Paradise of which Michelangelo speaks. The doors of the mosques in Cairo were of two kinds; those which, externally, were cased with sheets of bronze or iron, cut out in decorative patterns, and incised or inlaid, with bosses in relief; and those in wood, which were framed with interlaced designs of the square and diamond, this latter description of work being Coptic in its origin. The doors of the palace at Palermo, which were made by Saracenic workmen for the Normans, are fine examples and in good preservation. A somewhat similar decorative class of door to these latter is found in Verona, where the edges of the stiles and rails are beveled and notched. In the Renaissance period the Italian doors are quite simple, their architects trusting more to the doorways for effect; but in France and Germany the contrary is the case, the doors being elaborately carved, especially in the Louis XIV and Louis XV periods, and sometimes with architectural features such as columns and entablatures with pediment and niches, the doorway being in plain masonry. While in Italy the tendency was to give scale by increasing the number of panels, in France the contrary seems to have been the rule; and one of the great doors at Fontainebleau, which is in two leaves, is entirely carried out as if consisting of one great panel only. The earliest Renaissance doors in France are those of the cathedral of St. Sauveur at Aix (1503). In the lower panels there are figures 3 ft (0.91 m). high in Gothic niches, and in the upper panels a double range of niches with figures about 2 ft (0.61 m). high with canopies over them, all carved in cedar. The south door of Beauvais Cathedral is in some respects the finest in France; the upper panels are carved in high relief with figure subjects and canopies over them. The doors of the church at Gisors (1575) are carved with figures in niches subdivided by classic pilasters superimposed. In St. Maclou at Rouen are three magnificently carved doors; those by Jean Goujon have figures in niches on each side, and others in a group of great beauty in the center. The other doors, probably about forty to fifty years later, are enriched with bas-reliefs, landscapes, figures and elaborate interlaced borders. NASAs Vehicle Assembly Building at the Kennedy Space Center contains the four largest doors. The Vehicle Assembly Building was originally built for the assembly of the Apollo missions Saturn vehicles and was then used to support Space Shuttle operations. Each of the four doors are 139 meters (456 feet) high. The oldest door in England can be found in Westminster Abbey and dates from 1050. In England in the 17th century the door panels were raised with bolection or projecting moldings, sometimes richly carved, round them; in the 18th century the moldings worked on the stiles and rails were carved with the egg and tongue ornament.
Related accidents Doors : Door safety relates to prevention of door-related accidents. Such accidents take place in various forms, and in a number of locations; ranging from car doors to garage doors. Accidents vary in severity and frequency. According to the National Safety Council in the United States, 300,000 injuries are caused by doors every year. The types of accidents vary from relatively minor cases where doors cause damage to other objects, such as walls, to serious cases resulting in human injury, particularly to fingers, hands, and feet. A closing door can exert up to 40 tons per square inch of pressure between the hinges. Because of the number of accidents taking place, there has been a surge in the number of lawsuits. Thus organisations may be at risk when car doors or doors within buildings are unprotected. According to the US General Services Administration: ...It is essential that childrens fingers be protected from being crushed or otherwise injured in the hinge space of a swinging door or gate. There are simple devices available to attach to the hinge side, ensuring that this type of injury does not occur. As the door closes, the hand is pushed out of the opening, away from harm. In addition, young children are vulnerable to injury when they fall against the other (hinged) side of doors and gates, striking projected hinges. Piano hinges are not recommended to alleviate this problem as they tend to sag over time with heavy use. Instead, an inexpensive device fitting over hinges is available on the market and should be used to ensure safety... Outward and inward opening Whenever a door is opened outwards there is a risk that it could strike another person. In many cases this can be avoided by architectural design which favors doors which open inwards into rooms (from the perspective of a common area such as a corridor, the door opens outwards). In cases where this is infeasible, it may be possible to avoid an accident by placing windows in the door. However, inward-hinged doors can also escalate an accident by preventing people from escaping the building: people inside the building may press against the doors, and thus prevent the doors from opening. This was partly the case in the Grue Church fire in Norway in 1822. Today, the exterior doors of most large (especially public) buildings open outward, while interior doors such as doors to individual rooms, offices, suites, etc. open inward, as do many exterior doors of houses, particularly in North America. Doorstops Doorstops are simple devices used to prevent a door from coming into contact with another object (typically a wall). Without the door stop damage might be done to the wall. They may either absorb the force of a moving door, or hold the door in place to prevent unintended motion. Door guards The purpose of door guards (also known as hinge guards, anti-finger trapping devices, or finger guards) is to reduce the number of finger trapping accidents in doors, as doors pose a risk to children especially when closing. Door guards protect fingers in door hinges by covering the gap that is created by opening doors by covering the hinges of doors with a piece of rubber or plastic that wraps from the door frame to the door. There are also door safety products which eject the fingers from the push side of the door as it is being closed. There are various levels of door protection. Front door protection a front anti-finger trapping device but leaves the rear hinge pin side of the door unprotected. Full door protection uses front and rear anti-finger trapping devices and ensures the hinge side of a door is fully protected. Which level of protection is appropriate should be determined by a risk assessment of the door. There is also handle-side door protection, which prevents the door from slamming shut on the frame, which can cause injury to fingers/hands. Safety doors A safety door prevents finger injuries near the hinges without the use of door guards. Rather than cover the danger area, the approach is to change the shape of the door so that an accessible gap does not form in the first place. This is achieved by adding a perfectly circular ("bull-nose" shaped) extension to the door, which moves in and out of a cavity as the door opens and closes. This prevents any part of a hand being crushed near the hinges – either inside or outside. These doors have an operating range of slightly over 90 degrees, so their use is limited to where they come into contact with a side wall when fully open (or where they can be prevented from opening too far by a doorstop). Glass doors Glass doors pose the risk of unintentional collision if a person believes the door to be open when it is closed, or is unaware there is a door at all. This risk may be particularly pronounced with sliding glass doors because they often have large single panes which are hard to see. To prevent injury from glass doors, stickers or other types of warnings are sometimes placed on the glass surface to make it more visible. For instance, in the UK, Regulation 14 of the Workplace (Health and Safety Regulations) 1992 requires the marking of windows and glass doors to make them conspicuous. Australian Standards: AS1288 and AS2208 require glass doors to be made from laminated or toughened glass. Fire Special purpose fire doors are often employed in buildings to reduce the overall risk of fire, particularly by preventing the spread of fire and smoke. In cases where they are improperly installed, employed, or tampered with, the risk of fire can be increased. Door closers are sometimes used to ensure fire doors remain closed. An additional risk in a fire is that doors may prevent access to emergency services personnel in order to fight the fire, rescue occupants, etc. Door breaching techniques may be required in these situations to gain access. Panic bars are often used in buildings so that a door locked from the exterior can quickly and easily be opened from the inside in the event of a fire or other emergency. Vehicle doors There may be an increased risk of trapping hands or fingers in car doors compared to other types of doors, due to the proximity in which the occupant sits. In some car accidents, injury to occupants from the movement of car doors may occur Bicyclists often fear collision with an opening car door in case the cars occupant does not look carefully to check that it is safe to open the door. Because cyclists often ride near parked cars along the side of the road (see door zone) they are particularly vulnerable. Aircraft doors Doors which lead from interior, pressurized, sections of an aircraft to exterior or unpressurized areas can pose extreme risk if they are inadvertently opened during flight. This can be mitigated by having doors that open inwardly and are designed to be forced into their door frames by the internal cabin pressure – most cabin doors are of this type. However, an outward opening door is often advantageous for cargo doors to maximise available space, and these need to be secured by hefty locking mechanisms to overcome internal pressure. A number of accidents have occurred where outward-opening aircraft doors were opened in flight, often accidentally: • American Airlines Flight 96 (1972) • Turkish Airlines Flight 981 (1974) • United Airlines Flight 811 (1989).
Any content, trademark’s, or other material that might be found on the PapihillsTour.com website that is not PapihillsTour.com’s property remains the copyright of its respective owner/s. In no way does PapihillsTour.com claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.