Published at Wednesday, September 28th, 2016 - 15:30:13 PM. Door. By john.
Door types There are many types of door hinges. The main types include: Spring hinge a spring-loaded hinge made to provide assistance in the closing or the opening of the hinge leaves. A spring is a component of a hinge, that applies force to secure a hinge closed or keep a hinge opened. Barrel hinge a sectional barrel secured by a pivot. A barrel is a component of a hinge, that has a hollow cylinder shaped section where the rotational bearing force is applied to the pivot, and may also have a screw shaped section for fastening and/or driving the pivot. Pivot hinges which pivot in openings in the floor and the top of the door frame. Also referred to as a double-acting floor hinge. This type is found in ancient dry stone buildings and rarely in old wooden buildings. These are also called haar-hung doors. They are a low cost alternative for use with light weight doors. Butt/Mortise hinges usually in threes or fours, which are inset (mortised) into the door and frame. Most residential hinges found in the U.S. are made of steel, although mortise hinges for exterior doors are often made of brass or stainless steel to prevent corrosion. Case hinges Case hinges are similar to a butt hinge however usually more of a decorative nature most commonly used in suitcases, briefcases and the like. Continuous hinges, or piano hinges This type of hinge is also known as a piano hinge. It runs the entire length of the door, panel, or box. Continuous hinges are manufactured with or without holes. These hinges also come in various thicknesses, pin diameters, and knuckle lengths. Used for furniture doors (with or without self-closing feature, and with or without damping systems). They are made of two parts: One part is the hinge cup and the arm, the other part is the mounting plate. Also called "cup hinge", or "Euro hinge", as they were developed in Europe and use metric installation standards. Most such concealed hinges offer the advantage of full in situ adjustability for standoff distance from the cabinet face as well as pitch and roll by means of two screws on each hinge. Butterfly hinges, or Parliament (UK) Hinges These were known as dovetail hinges from the 17th century onwards and can be found on old desks and cabinets from about 1670 until the 18th century. The form of these hinges varied slightly between manufacturers, and their size ranged from the very large for heavy doors to the tiniest decorative hinge for use on jewellery boxes. Many hinges of this type were exported to America to support the home trades limited supply. They are still found to be both fairly cheap and decorative, especially on small items. Flag hinges A flag hinge can be taken apart with a fixed pin on one leaf. Flag hinges can also swivel a full 360 degrees around the pin. Flag hinges are manufactured as a right hand and a left hand configuration. Strap hinges An early hinge and used on many kinds of interior and exterior doors and cabinets. H hinges Shaped like an H and used on flush-mounted doors. Small H hinges (3–4 in or 76–102 mm) tend to be used for cabinets hinges, while larger hinges (6–7 in or 150–180 mm) are for passage doors or closet doors. HL hinges Large HL hinges were common for passage doors, room doors and closet doors in the 17th, 18th and even 19th centuries. On taller doors H hinges were occasionally used in the middle along with the HL hinges. Other types include: • Counterflap hinge • Flush hinge • Coach hinge • Rising Butt hinge • Double action spring hinge • Double action non-spring • Tee hinge • Friction hinge • Security hinge • Cranked hinge or stormproof hinge • Lift-off hinge • Self closing hinge
Butterfly doors : Butterfly doors or vertical doors are a type of door sometimes seen on high-performance cars. They are similar to scissor doors. While scissor doors move straight up via hinge points at the bottom of the A-pillar, butterfly doors move up and out via hinges along the A-pillar. This makes for easier entry/exit at the expense of requiring more opening space than needed for scissor doors. The McLaren F1, Alfa Romeo 33 Stradale, Saleen S7, Enzo Ferrari and its non road-going version, the FXX, Toyota Sera/EXY-10, and the Mercedes-Benz SLR McLaren, among others, use butterfly doors. It was also a common feature for Group C and IMSA GTP/Camel Lights prototype racers as they incorporate teardrop tops which allows the driver to get in and out of the car more quickly than conventional and gullwing doors, especially in a cramped pitlane environment such as the pre-1991 Le Mans circuit. Since then, butterfly doors have been an adopted design of closed top sportscar racers, such as the Toyota GT-One, Bentley Speed 8 and more recently, the Peugeot 908 HDi FAP. The Toyota Sera, made between 1990 and 1995, was a limited-release car designed exclusively for the Japanese market which used this design. The Mercedes-Benz SLR McLaren Roadster was one of the few open top cars to use butterfly wing doors. This is made possible by having the doors hinged at the side of A-pillar instead of at top by the roof. The McLaren MP4-12C has a unique system where the butterfly doors do not use a top hinge meaning that the car can use frameless windows which allows for the cars convertible version to retain them.
Any content, trademark’s, or other material that might be found on the PapihillsTour.com website that is not PapihillsTour.com’s property remains the copyright of its respective owner/s. In no way does PapihillsTour.com claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.